Nanoskin Speed Cut Cutting Compound

• Ultra-fast cutting compound
• Removes 1200 grit or finer sanding marks
• Great for removing scratches, defects, 
• acid rain and severe swirls/holograms

Unlike traditional compounds that leave compounding swirls, NANOSKIN® SPEED CUT Cutting Compound leaves a deep shine with no swirl marks. By using with MICROBUFF Cutting Pad, the abrasives cut quickly to remove 1200 grit sanding scratches, acid rain, and severe swirls and holograms. A quick pass with NANOSKIN® NANO CUT Finishing Compound will completely restore the shine and prepare the paint for wax. NANOSKIN® SPEED CUT is body shop safe, paintable, and contains no fillers. This safe, VOC compliant formula can be used on all paint finishes, including scratch-resistant and conventional clear coats.

DIRECTIONS:
For best results, use on clean, cool paint and out of direct sunlight.
Clean pad frequently using pad conditioner brush or compressed air using regulatory approved air nozzle.

Suggested Tools for Optimum Results-
FLEX XC 3401 VRG Dual Action Orbital Polisher
RUPES LHR 15ES Big Foot Random Orbital Polisher
RUPES LHR 21ES Big Foot Random Orbital Polisher

Removing 1,500 ~ 2,500 Grit Wet Sanding Marks-
1. Apply NANOSKIN® SPEED CUT Cutting Compound uniformly 
to MICROBUFF™ Cutting Pad. 
2. Buff at 4800 opm, working a 2’ x 2’ section.
3. Wipe residue off using a soft, clean microfiber towel.
4. Next use NANOSKIN® NANO CUT Finishing Compound with 
the same MICROBUFF™ Cutting Pad at 3800 - 4800 opm.
5. Make your own choice for finishing:
A. Apply NANOSKIN® FORMULA 67 Professional Quick 
Detailer with MICROBUFF™ Polishing Pad to add a layer of 
wax and restore showroom gloss. (Speed 3800 opm)
B. Apply NANOSKIN® SEAL NANO Perfect Sealant with 
MICROBUFF™ Finishing Pad to remove gloss-hindering 
defects while leaving a durable layer of paint protection 
behind. (Speed 3800 opm)

Removing 2,500 ~ 3,000 Grit Wet Sanding Marks or Finer Scratches-
1. Apply NANOSKIN® NANO CUT Finishing Compound uniformly 
to MICROBUFF™ Cutting Pad. 
2. Buff at 4800 opm, working a 2’ x 2’ section.
3. Wipe residue off using a soft, clean microfiber towel.
4. Make your own choice for finishing:
A. Apply NANOSKIN® FORMULA 67 Professional Quick 
Detailer with MICROBUFF™ Polishing Pad to add a layer of 
wax and restore showroom gloss. (Speed 3800 opm)
B. Apply NANOSKIN® SEAL NANO Perfect Sealant with 
MICROBUFF™ Finishing Pad to remove gloss-hindering 
defects while leaving a durable layer of paint protection 
behind. (Speed 3800 opm)

NOTE: PAD REJUVENATION 
The heavy and quick cutting of some polishers can cause the surface to become very hot and cause the oils in the polishes/compounds to prematurely flash off. 
One fine mist of NANOSKIN PAD REJUVENATOR to the center of the used pad is enough lubrication to reactivate the polishes/compounds left on the pad and get it back to a serviceable condition. 
DO NOT APPLY MORE POLISHES/COMPOUNDS TO THE PAD until all excess compound is removed off the pad and the pad is completely lubricated then apply a quarter size (1” diameter or 2.5 cm.) amount of product to center of pad.
More compound IS NOT the answer. After spraying PAD REJUVENATOR on the pad, you will find you will be able to finish a section without any additional compounds. There was a commercial many years ago saying, “A little dab will do you” and that’s the way this system works.